Programming Instructions

Fobik Programming Instructions

Programming When

Keys added or replaced.”FOBIK” Remotes (FOB Integrated Key)

How:

NOTE: Two programmed Completely Functional keys must be available for the following procedure to operate.

Note: Completely Functional means Remote and starting features of existing fobiks should be working

Obtain all keys.
Using first programmed key turn ignition switch ON and wait 3 seconds, return to OFFposition and remove key.

NOTE: First and second programmed key operations MUST be performed within 15 seconds.

Insert second programmed key and switch ignition ON.
Wait approximately 10 seconds.
Ensure immobilizer warning lamp begins to flash and an acoustic signal is emitted.
Switch ignition OFF and remove key.
Within 50 seconds, insert new key and switch ignition ON.
Wait approximately 10 seconds.
Ensure acoustic signal is emitted and immobilizer warning lamp remains illuminated for 3 seconds indicating programming completed.
For each additional key repeat procedure starting from the beginning.

Replacement keys can also be programmed using the diagnostic equipment.

GM Remote 15912860 Programming Instruction

Click here for online programming video

Use this Procedure for Vehicles with Driver Information Center

1. Insert Key and turn to ON position so you can access Driver Information Center.

2. Press the vehicle information button until PRESS TO RELEARN REMOTE KEY displays

3. Press the set/reset button until
REMOTE KEY LEARNING ACTIVE displays

4. Press and hold the lock and unlock buttons on the first keyless remote at the same
time for approximately 15 seconds. (On vehicles with memory recall seats, the first
remote learned with match driver 1 and the second will match driver 2.) A chime will sound indicating that the remote is programmed.

5. To program additional remotes at this time repeat step 4.
This vehicle can have a maximum of eight remotes programmed.

6. To exit programming mode turn the key off and remove.
Test remote(s).

Use this Procedure for Vehicles without Drivers Information Center

1. Insert key into ignition and turn to the on position.

2. Press the trip odometer reset stem until RELEARN REMOTE KEY displays.

3. Press and hold the trip odometer reset stem for three seconds. The message REMOTE KEY LEARNING ACTIVE will display 3. Press and hold the lock and unlock buttons on the first keyless remote at the same time for approximately 15 seconds. A chime will sound indicating that the remote is programmed

4. To program additional remotes at this time repeat step 3. This vehicle can have a maximum of eight remotes programmed.

5. turn key off and remove, test remotes.

GM Remote Programming 21997127 LHJ011

Programming instruction are for the following Vehicles.

Escalade (2003-2006), Avalanche (2003-2006),Silverado (2003-2007),SSR (2003-2004),Suburban (2003-2007),Tahoe (2003-2007),Sierra (2003-2007),Yukon (2003-2007),H1 (2003-2003),H2 (2003-2007),Torrent (2006-2007),Vue (2004-2007)

NOTE: Equinox 2005-2006 need dealership programming.

Instructions:

Hold down unlock button on door, not transmitter
While holding down, turn key on, off, on, off. (do not turn key all the way to start)
Leave key in off position and let go of the unlock button. Doors should lock and unlock and horn should beep. It is now in program mode.
Hold down the lock and unlock on the transmitter for approximately 30-60 seconds. The door locks will cycle when that transmitter is programmed. Take the next transmitter and do the same with it. After they are both programmed turn the key on and doors will cycle again and the horn will beep. This takes it out of program mode. You’re set to go.

Ford Transponder Key Programming

You will need to have the transponder key cut to match the original.

To program the new key you will first need both of the programmed keys that came with the vehicle. If you do not have both you will not be able to program the key yourself. You will need to go to the dealership or locksmith to have it done.

Instructions:

If you have both keys, put one of the already programmed keys into the ignition.
Turn the ignition to RUN but do not start the engine.
After the security light on the dash goes out, remove the key.
Put the next already programmed key into the ignition and turn the key to RUN, but do not start the engine.
Wait until the light on the dash goes out. Remove the key.
Take the new key and put it into the ignition.
Turn the key to RUN but do not start the vehicle.
Wait until the security light goes out on the dash then remove the key.
The new key should now be programmed.

Ford Remote Programming

You will need to have the working transponder key.

To program the new remote fob you will first need working key that came with the vehicle.

All the remotes must be programmed at the same programming procedure including

the working remotes that you already have.

Instructions:

Turn ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in
RUN. Door locks will cycle to confirm programming mode.
Within 20 seconds press any button on first keyless remote. Door locks will cycle
to confirm programming.
Within 20 seconds, press any button on second keyless remote or your existing remote. Door locks will
cycle again to confirm programming.
Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
Remote should now be programmed.

Chevrolet Buick Pontiac Saturn Hummer Key Programming

Click here for online programming video

Programming Instructions:

ALL KEYS LOST

1. Insert the new cut key into ignition cylinder and turn it to the ON position. The security light on the dash will illuminate and stay on for ten minutes. When the security light goes out, you have one minute to start the next step.

2. Turn the ignition cylinder to OFF and then back to the ON position. The security light on the dash will illuminate and stay on for ten more minutes. When the security light goes out, you have one minute to start the next step.

3. Turn the ignition cylinder to OFF and then back to the ON position. The security light on the dash will illuminate and stay on for ten more minutes.

4. After the security light has gone off for the third time, turn key off and remove from ignition. The key is now programmed and all other keys have been erased.

5. Insert key and start the vehicle to test key.

TO ADD AN EXTRA KEY

1. Insert an existing programmed working key into the ignition cylinder.

2. Turn ignition to the ON position for 5 seconds, then back to OFF position.

3. Remove the existing key and within 5 seconds insert new key and turn it to the ON position for 5 seconds.

4. Turn key OFF then back to ON. The key is now programmed. Start vehicle to test.

Toyota Remote Programming

Programming Instructions:

Begin with the key out of the ignition, drivers door is open, all other doors and trunk closed and drivers door is unlocked.
Perform these steps within 5 seconds: A. Insert the key into the ignition (Do NOT Turn it) and Pull key out. B. Insert the key into the ignition (Do NOT Turn it) and Pull key out.
Perform these steps within 40 seconds: A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition (Do NOT Turn it) and Pull key out.
Perform these steps within 40 seconds: A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in the ignition. D. Close the driver’s door. E. Turn the ignition to ON (Do NOT Start or crank engine) then back to OFF. F. Remove the key from the ignition.
Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point.
Perform these steps within 40 seconds: A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds. B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted. C. Repeat steps A and B in step 6 for each new remote.
Open drivers door. Programming is complete.

Nissan Remote Key Fob Programming

Get in the driver seat and close all the doors. Lock all the doors using the driver’s side power lock/unlock switch.
Insert the key into the ignition and remove it from ignition 6 times or more within 10 seconds. Make sure you remove it from the ignition cylinder fully each time. *If you remove it too fast, the system will not enter the programming mode. The hazard lamps will begin to flash if you followed the procedure correctly.
Once the system enters the programming mode, insert the key into the ignition cylinder once again and turn to the ON position without starting the car.
Within 5 seconds, push any button only once on the remote transmitter. Your hazard lamps should flash. If you push the button more than once, the procedure will not work.
If you are programming more than one remote, including the old ones, unlock then lock all the doors again using the driver’s side power lock/unlock switch and within 5 seconds, push any button on the next remote. Hazard lamps will flash.
Repeat this step for each remote. Turn the key to the OFF position and remove the key from the ignition, unlock the doors using the driver’s side power lock/unlock and open the driver side door.

Chrysler Transponder Key Programming

NOTE: Two programmed key transmitters must be available for the following procedure to operate. If none available key transmitters can only be programmed using the diagnostic equipment.
- Insert the first programmed key into ignition switch.
- Switch ignition ON for at least 3 seconds but no longer than 15 seconds.
- Turn ignition OFF and remove the key.
- Within 15 seconds insert the second programmed key into ignition switch and turn ignition ON.
- After 10 seconds an acoustic signal will be heard and immobilizer warning lamp will flash.
- Turn ignition OFF and remove the second programmed key.
- Within 60 seconds insert non-programmed key into ignition switch and turn ignition ON.
- After 10 seconds an acoustic signal will be heard and immobilizer warning lamp will illuminate for 3 seconds.
- Switch ignition OFF.
- Remove Key.
Check operation of the programmed key transmitter. Repeat procedure for additional key transmitters if required.

.

Chrysler Jeep Dodge Remote Head Key Programming

Key Portion Programming:

NOTE: Two programmed key transmitters must be available for the following procedure to operate. If none available key transmitters can only be programmed using the diagnostic equipment.

Insert the first programmed key into ignition switch.
Switch ignition ON for at least 3 seconds but no longer than 15 seconds.
Turn ignition OFF and remove the key.
Within 15 seconds insert the second programmed key into ignition switch and turn ignition ON.
After 10 seconds an acoustic signal will be heard and immobilizer warning lamp will flash.
Turn ignition OFF and remove the second programmed key.
Within 60 seconds insert non-programmed key into ignition switch and turn ignition ON.
After 10 seconds an acoustic signal will be heard and immobilizer warning lamp will illuminate for 3 seconds.
Switch ignition OFF.
Remove Key.

Check operation of the programmed key transmitter. Repeat procedure for additional key transmitters if required.

Remote Portion Programming:

NOTE: One programmed Remote transmitters must be available for the following procedure to operate.

Obtain all remote transmitters.

NOTE: Any existing remote transmitters not used during programming will become inoperative.

Switch ignition ON.

Using a programmed remote transmitter proceed as follows.

Press and hold remote transmitter UNLOCK button.
After holding the UNLOCK button for at least 4 seconds but no longer than 10 seconds, press the remote transmitters panic button for at least 1 second and release both buttons.
Ensure acoustic signal is emitted indicating programming mode active.
Within 30 seconds carry out the following procedure for each remote transmitter (including previously programmed remote transmitter)
Press any button of each remote transmitter to be programmed.
Ensure acoustic signal is emitted after each remote transmitter operation.
Programming must be completed within 30 seconds.
Switch ignition OFF or wait 32 seconds to exit programming mode.

Ensure final acoustic signal is emitted. Replacement remote transmitters can also be programmed using the diagnostic equipment.

Programming Instruction for Chevrolet Buick GM Flip keys

Programming Instructions:

Note:

• To initiate, this procedure requires that a learned master key be available.• This procedure adds keys only. The procedure does not erase previously learned keys.• The keys to be learned must duplicate the mechanical cut of the current key.
• If more than one valet key is to be learned, immediately precede each valet key with a learned master key.

1) Place an already programmed key in the keyway (ignition). Cycle the ignition from OFF to ON.

2) Within 15 seconds, insert the new, properly cut transponder key in the ignition. Turn the key to ON (RUN) or START. The “security” indicator light will go on and off. Turn the key “OFF”.

3) The key will now start the car. Repeat the second step for each new key to be programmed.

Subaru Remote Programming

Instruction:

Obtain all remote transmitters for this vehicle.

For remote programming on this vehicle, it is necessary to obtain the identification number on the circuit board in the remote.

Take a small screwdriver and split the case halves of the remote. Once open you will look on the circuit board and see a sticker with 8 digits on it. If there are two rows of digits you need the one with all numbers and no letters.

Now you are ready for programming.

1. Sit in the vehicle and close the door. Ensure that all doors and rear gate or trunk lid are closed.

2. Open then close the driver’s door.

3. Open then close the driver’s door within 45 seconds.

4. Cycle the ignition switch from LOCK to ON 10 times within 15 seconds. Once done properly you will hear an audible tone accompanied with a buzzing noise. At the same time the interior light will begin to flash. The flashing light and the buzzing sound will continue through the programming process. If you do not get this response then you must return to step 3 and start over.

5. Open and close the door within 15 seconds and the audible tone will be heard again. If you do not get the audible tone at this time you must return to step 3 and start over.

6. While you still hear the tone, press the LOCK button on the door panel the same amount of times as the first digit on the identification number, if the first number is 2 you will press the LOCK button twice, if the number is 8 you will press the LOCK button eight times. Once the first sequence is entered for the first number you will press the UNLOCK button once within five seconds. Repeat these steps for the seven remaining digits of the identification number. Press the UNLOCK button within five seconds after each number entry.

7. Once finished entering all numbers in the identification number you must press the UNLOCK button one more time within 5 seconds and then go through step 6 one more time. You must complete all steps in step 6 one additional time. At completion of the eighth digit you will hear an audible tone for approximately 30 seconds.

8. Repeat steps 4-7 for each additional remote you are programming to the vehicle. 9. Upon completion you can remove key from ignition and test all remotes to ensure that the programming was successful.

Chrysler Dodge Jeep Remote Programming

This programming procedure requires you to already have at least 1 working remote transmitter for your Dodge/Chrysler/Jeep. If you do not have any remote transmitters you must get this new one programmed by a qualified locksmith or dealership. Please review the procedure before attempting programming. There are 2 possible programming procedures available. Please try procedure 1 first. If that does not work, use procedure 2

Programming procedure #1.
Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.
1. Put key in ignition and turn ignition switch to ON position (last stop before cranking the engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. Achime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the Unlock button on the remote used in step 3. You should hear an audible tone indicating that remote has been re-programmed. This step must be done within 30 seconds of hearing the first chime in step 3.
5. Within 30 seconds – Press the Unlock button on the next remote.
-Repeat step 5. for all additional remotes including working remotes
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

Programming Procedure #2
Obtain all remote transmitters for this vehicle. Sit in the vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.
1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the LOCK and UNLOCK buttons simultaneously on the same remote used in step 3. then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. This must be done within 30 seconds of step 3.
5. Within 30 seconds – Press the LOCK and UNLOCK button on the next remote then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. Repeat step 5. for all additional remotes including working remotes.
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming

Toyota Car Key Programming

TOYOTA TRANSPONDER KEY PROGRAMMING UP TO 2002

Please try the procedure below. YOU MUST HAVE A MASTER. IF YOUR KEY THAT YOU ARE CURRENTLY USING IS A COPY OR CLONE. THE PROCEDURE BELOW WILL NOT NOT. If you still have any questions, please let me know. Thank you.

Obtain one black programmed master key

1. Insert the black programmed key into the ignition.

2. Press and release accelerator pedal 5 times within 15 seconds of inserting key into ignition.

3. Press and release brake pedal 6 times within 20 seconds of step 2.

4. Remove black key from ignition switch.

5. Insert unprogrammed key into ignition within 10 seconds of step 4.

6. Press and release accelerator pedal once within 10 seconds of step 5.

7. Once these steps are performed properly you will see the immobilizer warning lamp begin to flash and after one minute the lamp will stop flashing. Once the immobilizer warning lamp stops flashing you will have ten seconds to insert an additional key to be programmed.

8. Within ten seconds of inserting key into ignition press and release accelerator pedal once.

9. Immobilizer warning lamp will flash and after one minute the lamp will shut off.

Share this:

Like this: